Author
|
Thread |
|
|
dfcas
Joined: 11 Jan 2004
Posts: 2815
Location: hillbilly heaven3/7/21 9:49 AM |
OT:Car wax
Need to do this and was wondering what people like. I prefer easy to install and long lasting. Don't care much about appearance or cost. The stuff I've been using came out in the 70's and I'm sure theres a better choice now. I've read a little about graphene.
|
|
|
|
|
|
|
|
Sparky
Joined: 08 Dec 2003
Posts: 19083
Location: PDX3/7/21 12:47 PM |
Can't recall the last time I waxed a car. ;)
I have been washing with a small amount of Cascade DW powder in the bucket [with soap] for years. I first started doing this with the idea to try to get the water spots minimized.
I used to towel dry vehicles in the shade after a wash, not done that in years either. But I do use my leaf blower to get water off after a wash. I hate to work hard at making cars look good, not doing it, rater be riding...
Not had a car more than 3 years since I started doing this, but water beads still up to that point FWIW.
|
|
|
|
|
|
|
|
|
Sparky
Joined: 08 Dec 2003
Posts: 19083
Location: PDX3/7/21 6:41 PM |
I never want anything that nice... ;O
|
|
|
|
|
|
|
|
Craig
Joined: 12 Jan 2004
Posts: 591
3/8/21 6:08 PM |
Forgive my ignorance (there's a first for the internet...) but doesn't the wax/polish depend heavily on what paint process is used? I vaguely remember being told to never use wax on a Honda Civic my father owned for a while; that there was a clear coat that required a special replenisher for it. I have a 97 Mazda that's a single stage paint and it's more traditional wax friendly.
Paints can be complicated these days? Or was Honda selling my father magic paint beans?
|
|
|
|
|
|
|
|
Tom Price
Joined: 11 Jan 2004
Posts: 505
Location: Rochester, NY3/8/21 6:38 PM |
Magic Beans
Wax is fine on clear coat. 99% of the current waxes are safe to use. You do not want to use a highly abrasive polish or rubbing compound as the scratching will give a fogging effect to the clear coat.
|
|
|
|
|
|
|
|
Craig
Joined: 12 Jan 2004
Posts: 591
3/8/21 10:19 PM |
My (mis)information was garnered nearly 2 decades ago. I wonder if waxes were less clear coat friendly back then. Regardless, good to know. The classic Mazda Miata NA is the only car I own that I care enough to wax and its paint process primitive enough to not require a whole lot of special attention. (rust free, less than 60,000 miles, increasing in value by 15-20% every year for some absurd reason). Because of this thread and TheInternet™ I've been inspired to buy a clay bar. Any reason I shouldn't?
|
|
|
|
|
|
|
|
dfcas
Joined: 11 Jan 2004
Posts: 2815
Location: hillbilly heaven3/9/21 9:41 AM |
I've always used non abrasive wax on cars with clear coat. Not sure if any modern cars don't have clearcoat.
|
|
|
|
|
|
|
|
Tom Price
Joined: 11 Jan 2004
Posts: 505
Location: Rochester, NY3/9/21 10:02 AM |
Craig,. There is no reason to not use a clay bar system. It is very easy to use, just use plenty of the enclosed spray and the bar just glides along. You should be able to wash, clay bar, and wax a small car like your Miata in just a couple of hours.
|
|
|
|
|
|
|
|
Brian Nystrom
Joined: 26 Jan 2004
Posts: 5101
Location: Nashua, NH3/9/21 10:28 AM |
I used a clay bar once and although it does add significantly to the time required, the resulting finish is pretty amazing!
That said, I'm really not into exterior aesthetic maintenance on my cars, so I haven't used it since.
|
|
|
|
|
|
|
|
Andrew Lee
Joined: 10 Jan 2004
Posts: 85
Location: Anchorage3/14/21 11:49 PM |
quote:
The stuff I've been using came out in the 70's and I'm sure theres a better choice now.
Nu Finish? That's still quick and easy, long lasting, cheap, and compares well to more expensive choices. Good enough for the car that I baby (an 18 year old Subaru). I like to clay bar before - it goes fast the subsequent times after the initial time on an old car. I just do it while I'm washing the car if the paint doesn't feel smooth from dirt remaining after the wash.
|
|
|
|
|
|
|
|
greglepore
Joined: 10 Jan 2004
Posts: 1724
Location: SE Pa, USA4/4/21 6:52 AM |
Clay bar followed by Opti-Seal. You literally mist this on a sponge, just wipe it on, no buffing req'd, and it leaves a ceramic like coating that's good for almost a year. Awesome stuff.
|
|
|
|
|
|
|
|
PLee
Joined: 08 Dec 2003
Posts: 3713
Location: Brooklyn, NY4/4/21 6:06 PM |
Have you tried Hyper Seal?
|
|
|
|
|
|
|
|
Sparky
Joined: 08 Dec 2003
Posts: 19083
Location: PDX4/4/21 10:19 PM |
I have some Polymer based Meguiars Ultimate. I have used it on painted bikes mostly. Originally got it 'for I forget which car' a few years back. It was pricey, but I bet my van used 2 oz today. I did not get up and do the roof yet though. It was a lot less work on the white van in todays cooler temp than on the dark blue CRV I last used it on in hotter conditions.
|
|
|
|
|
|
|
|
greglepore
Joined: 10 Jan 2004
Posts: 1724
Location: SE Pa, USA4/6/21 3:31 PM |
Parkin-I haven't but its by the same folks... . Suspect it lives up to the claims.
|
|
|
|
|
|
|
|
|